Ford Mustang Service Manual: Disassembly

Disassembly

1. CAUTION: Do not place the cylinder head (6049) flat on the bench; the valves will bend.

CAUTION: Before disassembly begins, mark the valve position on the face of each valve being removed. The valves must be re-installed into the same positions.

Install the special tool.

2. Remove the exhaust camshaft sprocket and the intake camshaft bolt,


2. Remove the exhaust camshaft sprocket and the intake camshaft bolt, washer and spacer.

3. Compress the tensioner (6L266) and install a lock pin.


3. Compress the tensioner (6L266) and install a lock pin.

4. Remove the special tool.


4. Remove the special tool.

5. Remove the timing chain (6268) and the camshaft sprocket (6256).


5. Remove the timing chain (6268) and the camshaft sprocket (6256).

6. NOTE: LH tensioner is shown, RH tensioner is similar.


6. NOTE:

LH tensioner is shown, RH tensioner is similar.

Remove the tensioner.

7. Remove the roller followers on the base circle.


7. Remove the roller followers on the base circle.

1. Install the special tool on the valve spring.

2. Compress the tool and remove the roller follower.

8. Repeat the previous step for the remaining roller followers.


8. Repeat the previous step for the remaining roller followers.

9. Remove the hydraulic lash adjusters.

10. CAUTION: Make sure the tool is seated correctly on the valve


10. CAUTION: Make sure the tool is seated correctly on the valve spring. Apply a small amount of air at a time. This will prevent the tool from shifting and causing damage to the cylinder head.

Install the air-operated spring compressor on the cylinder head.

11. Compress the valve spring compressor and remove the key from the


11. Compress the valve spring compressor and remove the key from the valves.

12. Remove the intake valves and the valve springs.


12. Remove the intake valves and the valve springs.

1. Release the pressure and remove the valve spring compressor.

2. Remove the intake valves and the valve springs from the cylinder head.

13. Remove the valve stem seals.


13. Remove the valve stem seals.

14. CAUTION: The outer bolts on the outer cam bearing cap (exhaust)


14. CAUTION: The outer bolts on the outer cam bearing cap (exhaust) are longer and must be returned to the same location or engine damage may occur.

NOTE

: Identify the camshaft-to-cylinder head location. Caps are not interchangeable.

Remove the bolts and the camshaft bearing cap assemblies.

15. Remove the camshafts (6250).


15. Remove the camshafts (6250).

Assembly


    Cylinder Head
    Engine (Description and Operation) WARNING: Do not operate the engine with the hood open until the fan blade has been first examined for possible cracks and separation. The 4.6L (4V) (281 CID) Cobra ...

    Assembly
    Disassembly 1. CAUTION: Do not place the cylinder head (6049) flat on the bench; the valves will bend. CAUTION: Before disassembly begins, mark the valve position on the face of each valve being re ...

    Other materials:

    Compressor to Condenser Discharge Line - 4.6L
    Air Conditioning (Description and Operation) The A/C refrigerant system is a clutch cycling orifice tube type. The system components are: A/C compressor (19703) A/C clutch (2884) A/C condenser core (19712) A/C evaporator core (19860) suction accumulator ...

    Removal
    Removal 1. Remove the nuts and position the radio ignition interference capacitors aside. 2. Remove the valve covers. For additional information, refer to Valve Cover RH and Valve Cover LH in this section. 3. Remove the cooling fan. 4. Remove the accesso ...

    Idle Air Control (IAC) Valve - 4.6L (2V)
    Electronic Engine Controls (Description and Operation) The electronic engine controls consist of the following: powertrain control module (PCM) throttle position (TP) sensor idle air control (IAC) valve engine coolant temperature (ECT) sensor ...