Ford Mustang Service Manual: Master Cylinder

Hydraulic Brake Actuation (Description and Operation)

 


 

CAUTION: Blistering or swelling of rubber brake components may indicate


CAUTION: Blistering or swelling of rubber brake components may indicate contamination of the brake fluid by a petroleum based substance. New rubber components must be installed in the hydraulic brake system if contaminated and the entire hydraulic brake system must be flushed with clean brake fluid to prevent recontamination.

This vehicle is equipped with a brake pedal actuated dual brake system. The system consists of the following:

  • power brake booster (2005)
  • brake master cylinder (2140)
  • brake pressure control valve (2B091)
  • disc brake calipers (2B120)
  • rear disc brake calipers (2553)
  • brake tubes and hoses
  • anti-lock brake system (ABS) components

The dual brake system is split front and rear with the front wheel brakes comprising of one circuit and the rear wheel brakes, the other circuit.

Brake Fluid

WARNING: Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with eyes. Wash hands thoroughly after handling. If brake fluid contacts eyes, flush with running water for 15 minutes. Get medical attention if irritation persists. If taken internally, drink water and induce vomiting. Get medical attention immediately.

Clean, fresh Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A is the only brake fluid that should be used in Ford vehicles.

  • Do not reuse brake fluid drained or bled from the system.
  • Do not use brake fluid that has been stored in an open container.
  • Do not mix different types of brake fluid.

Brake Master Cylinder

The brake master cylinder is a dual piston type. The brake master cylinder operates as follows:

  • When the brake pedal (2455) is depressed, pressure is applied by mechanical linkage to the primary and secondary piston.
  • Brake master cylinder pistons apply hydraulic pressure to the two hydraulic circuits.
  • Brake master cylinder will not be overhauled, a new master cylinder is installed only.

The brake master cylinder consists of:

  • brake master cylinder reservoir (2K478)
  • brake master cylinder body

Brake Master Cylinder Reservoir

NOTE: Whenever the brake master cylinder reservoir is removed from the brake master cylinder, new grommets must be installed.

The brake master cylinder reservoir :

  • is mounted to the brake master cylinder.
  • holds fluid supply for each brake master cylinder hydraulic piston.
  • provides visual fluid level markings.
  • contains the brake master cylinder fluid level sensor.

Brake Pressure Control Valve

The brake pressure control valve proportions the pressure to the rear brakes.

  • When the brake pedal is applied, brake fluid pressure passes through the proportioning valves to the rear brake system until the valve split point is reached.
  • Above its split point, the proportioning valve begins to reduce the hydraulic pressure to the rear brakes, creating a balanced braking condition between the front and rear brakes.

Brake Tubes and Hoses

CAUTION: Never use copper tubing. It is subject to fatigue, cracking and corrosion which could result in brake tube failure.

Steel tubing is used throughout the brake hydraulic system. All brake tube fittings must be correctly double flared to provide strong leakproof connections. When bending the tubing to fit the underbody or rear axle contours, be careful not to kink or crack the tube.

If a section of brake tube is damaged, the entire section must be removed and a new tube of the same type, size, shape and length installed.

When replacing hydraulic brake tubing, hoses, or connectors, tighten all connections securely. After installation, bleed the brake system.

    Pedal and Bracket
    Hydraulic Brake Actuation (Description and Operation)   CAUTION: Blistering or swelling of rubber brake components may indicate contamination of the brake fluid by a petroleum based substance ...

    Master Cylinder - Hydro-Boost
    Hydraulic Brake Actuation (Description and Operation)   CAUTION: Blistering or swelling of rubber brake components may indicate contamination of the brake fluid by a petroleum based substance ...

    Other materials:

    Anti-theft system
    The active anti-theft system is designed to warn you in the event of unauthorized vehicle entry and is also designed to help prevent unwanted towing of the vehicle. You can choose what is monitored by arming the system in different ways. Partial Monitor Mo ...

    General information
    WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility i ...

    Removal
    Removal WARNING: Do not smoke, carry lighted tobacco or an open flame of any type when working on or near any fuel-related components. Highly flammable mixtures are always present and may be ignited, possibly resulting in personal injury. WARNING: Fuel suppl ...