Ford Mustang Service Manual: Deactivation

Deactivation

WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.

WARNING: After deployment, the air bag surface can contain deposits of sodium hydroxide, a product of the gas generant combustion that is irritating to the skin. Wash your hands with soap and water afterwards.

WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.

WARNING: Air bag modules with discolored or damaged trim covers must be installed new, not repainted.

WARNING: The restraint system diagnostic tool is for restraint system service only.

Remove from vehicle prior to road use. Failure to remove could result in injury and possible violation of vehicle safety standards.

1. WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors, such as doors, instrument panel, console, door latches, strikers, seats and hood latches.

Please refer to the appropriate vehicle shop manual to determine location of the front air bag sensors.

The side air bag sensors are located at or near the base of the B-pillar.

To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).

Disconnect the battery ground cable and wait at least one minute.

2. Remove the steering column opening lower finish panel.

1. Remove the screws.

2. Pull out to release the retaining clips and remove the steering column opening lower finish panel.

3. Remove the steering column opening lower reinforcement.


3. Remove the steering column opening lower reinforcement.

1. Remove the bolts.

2. Remove the steering column opening lower reinforcement.

4. Pushing in on the release tab, disconnect the clockspring electrical


4. Pushing in on the release tab, disconnect the clockspring electrical connector at the base of the steering column.

5. Attach the restraint system diagnostic tool to the vehicle harness side of


5. Attach the restraint system diagnostic tool to the vehicle harness side of the clockspring electrical connector.

6. Open the glove compartment, push in on the tabs and open the glove


6. Open the glove compartment, push in on the tabs and open the glove compartment door to its fullest extent.

7. Remove the right hand A/C register duct.


7. Remove the right hand A/C register duct.

  • Remove the two screws retaining the duct to the A/C register.
  • Separate the A/C duct at the air plenum and remove the duct.

8. Disconnect the passenger air bag module.

9. Attach the restraint system diagnostic tool to the vehicle harness side of


9. Attach the restraint system diagnostic tool to the vehicle harness side of the passenger air bag electrical connector.

10. Connect the battery ground cable.


10. Connect the battery ground cable.

11. With the restraint system diagnostic tools installed at all deployable devices, prove out the supplemental restraint system (SRS).

12. Disconnect the battery ground cable and wait at least one minute.

    Supplemental Restraint System (SRS) Deactivation and Reactivation
    Steering Column (Description and Operation)   NOTE: All fasteners are important because they can affect the performance of vital parts and systems. Incorrect installation of the fasteners ...

    Reactivation
    Deactivation WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the ...

    Other materials:

    Camber and Caster Adjustment - Front
    Wheel Alignment Angles Camber and toe are adjustable on the front suspension systems. Front camber is adjusted by moving the top of the strut and spring assembly. Rear camber is adjusted by means of eccentric cams on the rear upper arms. Caster is preset at ...

    Wiring Harness
    Fuel Charging and Controls The fuel injection supply manifold (9F792): delivers fuel to the fuel injector. receives fuel from the fuel supply line. The throttle body: controls air supply to the upper intake manifold by positioning the throttle plate. ...

    Symptom Chart
    Inspection and Verification 1. Verify the customer's concern by operating the climate control system to duplicate the condition. 2. Inspect to determine if one of the following mechanical or electrical concerns apply: Visual Inspection Chart Mechan ...