Ford Mustang (1999-2004) Service Manual: Disassembly
1. CAUTION: Hand tighten the special tool to prevent gear damage.
CAUTION: Support the output shaft while using the press to prevent damage to the shaft or gears.
Using the special tool and a press, remove first gear, the output shaft rear bearing and the fifth driven gear.
- Discard the output shaft bearing.
- Inspect the gear for wear or damage. Install a new gear as necessary.
2. Remove the first gear needle bearing.
- Inspect the needle bearing for wear or damage. Install a new needle bearing as necessary.
3. Remove and discard the snap ring.
4. Remove the first gear synchronizer thrust washer, the inner cone, the friction cone and the first gear synchronizer blocking ring.
- Inspect all components for wear or damage. Install new components as necessary.
5. Remove the synchronizer spring, then remove the synchronizer sleeve.
6. NOTE: Install the special tool behind second gear with the flat side of the tool facing second gear.
Using the special tool, remove the second gear, the second gear synchronizer thrust washer, the inner cone, the friction cone, the second gear synchronizer blocking ring and the synchronizer hub.
- Inspect the gear for wear or damage. Install a new gear as necessary.
- Inspect the all synchronizer components for wear or damage. Install a new components as necessary.
7. Remove the second gear needle bearing.
- Inspect the needle bearing for wear or damage. Install a new needle bearing as necessary.
8. NOTE: Reposition the output shaft on the press with the input shaft end facing upward.
Remove and discard the snap ring, then using the special tool, remove the third/fourth gear synchronizer assembly, the third gear synchronizer blocking ring and the third gear.
- Inspect the gear for broken or cracked teeth. Install a new gear as necessary.
9. Remove the third gear needle bearing.
- Inspect the needle bearing for wear or damage. Install a new needle bearing as necessary.
10. NOTE: Install the special tool with the flat side facing the bearing.
Using the special tool, press the output shaft front bearing from the output shaft.
11. Inspect the synchronizers.
- Check for worn, nicked or broken teeth. Install a new synchronizer as necessary.
- Check keys for wear or distortion. Install a new synchronizer as necessary.
- Check springs for distortion. Install a new synchronizer as necessary.
12. Inspect the synchronizer blocking rings.
- Check for wear or damage. Install new synchronizer blocking rings as necessary.
- Check the clearance between the synchronizer blocking ring and the gear.
- Position the blocking ring onto the gear. Make sure the correct blocking ring is measured with the correct gear and that the blocking ring is fully seated on the gear.
- Insert a feeler gauge and measure the clearance, while applying pressure and rotating the blocking ring. The measurement should be the same around the entire circumference. If the clearance is less than 0.38 mm (0.015 in), install new blocking rings.
13. Inspect the output shaft for scoring or worn or damaged splines. Install a new output shaft as necessary.
Output Shaft
Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) Adapter for 303-224 (Handle) 205-153 (T80T-4000-W) Installer, Output Shaft Rear Bearing 308-401 ...Assembly
1. Lubricate all components with the recommended transmission fluid when reassembling. 2. Using the special tools, press the output shaft front bearing on the output shaft. 3. Install the third g ...Other materials:
Engine
WARNING: Do not operate the engine with the hood open until the fan
blade has been first
examined for possible cracks and separation.
The 4.6L (4V) (281 CID) is a V-8 engine with the following features:
dual overhead camshafts
four valves per cylinder
s ...
Accelerator Cable - 3.8L
Removal and Installation
1. Push the accelerator cable nylon bushing out of the accelerator pedal and
shaft arm.
2. Remove the bolts retaining the accelerator cable to the dash panel.
3. Disconnect the accelerator cable from the throttle body by rotating ...
Vacuum Hose Repair - Mini-Tube
Special Tool(s)
Vacuum Pump Kit
416-D002 (D95L-7559-A) or
equivalent
1. Measure the length of the damaged area of the mini-tube vacuum hose.
2. Cut a piece of standard 1/8 inch inner diameter vacuum hose approximately 25
mm (1 inch
longer t ...