Ford Mustang (1999-2004) Service Manual: Electronic Pressure Control (EPC) Solenoid

Special Tool(s)

Gauge, Transmission Solenoid Connectors 307-426

Removal

1. Remove the manual control lever. For additional information, refer to Manual Control Lever Shaft and Seal in this section.

2. CAUTION: Do not pull on the molded lead frame. This may cause damage to the connector ends. Carefully pry up on the locking tabs to disconnect the solenoids.

Disconnect the molded lead frame from the solenoids.

Disconnect the molded lead frame from the solenoids.

1. Disconnect the shift solenoid SSA and SSB.

2. Disconnect the torque converter clutch (TCC).

3. Disconnect the electronic pressure control (EPC) solenoid.

4. Disconnect the bulkhead inter-connector.

Electronic Pressure Control (EPC) Solenoid

3. Remove the EPC solenoid.

1. Remove the bolt and EPC solenoid bracket.

2. Remove the EPC solenoid.

Electronic Pressure Control (EPC) Solenoid

Installation

1. Install the EPC solenoid.

1. Install the EPC solenoid.

2. Install the EPC solenoid bracket and bolt.

Electronic Pressure Control (EPC) Solenoid

2. Inspect the lead frame for damage.

  • Using the special tool, check all lead frame solenoid connections. The gauge should fit tightly and not fall out after being inserted.
  • If the special tool passes through any lead frame connector pins or does not feel like it makes a good contact, install a new lead frame.

Electronic Pressure Control (EPC) Solenoid

3. Connect the molded lead frame to the solenoids.

  • Connect the bulkhead inter-connector by pressing it in place by hand and fully seating the connector in place.
  • Connect the EPC solenoid by pressing it in place by hand and fully seating the connector in place. Make sure that the terminals pass fully through the connector slots.
  • Connect the TCC by pressing it in place by hand and fully seating the connector in place. Make sure that the terminals pass fully through the connector slots.
  • Connect the shift solenoid SSA and SSB by pressing it in place by hand and fully seating the connector in place. Make sure that the terminals pass fully through the connector slots.

Electronic Pressure Control (EPC) Solenoid

4. Install the manual control lever. For additional information, refer to Manual Control Lever Shaft and Seal in this section.

    Extension Housing Seal and Gasket
    Special Tool(s) Slide Hammer 100-001 (T50T-100-A) Installer, Transmission Extension Housing Fluid Seal 308-002 (T61L-7657-A) Remover, Transmission Fluid Seal ...

    Manual Control Lever Shaft and Seal
    Special Tool(s) Installer, Shift Shaft Fluid Seal 307-050 (T74P-77498-A) Alignment Gauge, TR Sensor 307-351 (T97L-70010-A) Removal 1. Drain the transmission fluid and re ...

    Other materials:

    Support Straps
    Removal WARNING: Do not smoke, carry lighted tobacco or an open flame of any type when working on or near any fuel-related components. Highly flammable mixtures are always present and may be ignited, possibly resulting in personal injury. WARNING: Fuel suppl ...

    Output Shaft
    Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) Adapter for 303-224 (Handle) 205-153 (T80T-4000-W) Installer, Output Shaft Rear Bearing 308-401 Remover/Installer, Bearing Tube 308-025 (T75L-7025 ...

    Speed Control (Diagnosis and Testing)
    Refer to Wiring Diagrams Cell 31 , Speed Control for schematic and connector information. Special Tool(s) Worldwide Diagnostic System (WDS) 418-F224, New Generation STAR (NGS) Tester 418-F052, or equivalent diagnostic tool 7 ...