Ford Mustang Owners Manual: Engine coolant check

Checking the Engine Coolant

The concentration and level of engine coolant should be checked at the intervals listed in Scheduled Maintenance Information.

Note

: Make sure that the level is at the FULL COLD level or within the COLD FILL RANGE in the coolant reservoir.

Note

: Coolant expands when it is hot. The level may extend beyond the COLD FILL RANGE.

If the level is below the COLD FILL RANGE, add coolant immediately.

See Adding Engine Coolant in this chapter.

The coolant concentration should be maintained at 50%, which equates to a freeze point between -34°F (-37°C).

Note

: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300ROB75240 available from your dealer. Ford does not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations.

Note

: Automotive fluids are not interchangeable; do not use engine coolant/antifreeze or windshield washer fluid outside of its specified function and vehicle location.

Adding Engine Coolant

WARNING

: Do not add engine coolant when the engine is hot.

Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.

WARNING

: Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.

WARNING

: To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap.

The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly.

WARNING

: Do not add coolant further than the MAX mark of the COLD FILL RANGE.

Note

: Do not use stop leak pellets or cooling system sealants or additives as they can cause damage to the engine cooling and or heating systems. This damage would not be covered under your vehicle’s warranty.

Note

: During normal vehicle operation, the engine coolant may change color from orange to pink or light red. As long as the engine coolant is clear and uncontaminated, this color change does not indicate the engine coolant has degraded nor does it require the engine coolant to be drained, the system to be flushed, or the engine coolant to be replaced.

• DO NOT MIX different colors or types of coolant in your vehicle.

Make sure the correct coolant is used. Mixing of engine coolants may harm your engine’s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty.

• A large amount of water without engine coolant may be added, in case of emergency, to reach a vehicle service location. In this instance, the cooling system must be drained, chemically cleaned with Motorcraft® Premium Cooling System Flush, and refilled with engine coolant as soon as possible. Water alone (without engine coolant) can cause engine damage from corrosion, overheating or freezing.

• Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing.

• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant.

Unscrew the cap slowly. Any pressure will escape as you unscrew the cap.

Add prediluted engine coolant meeting the Ford specification. See the technical specifications chart in theCapacities and Specifications chapter.

Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle.

If necessary, add enough engine coolant to bring the coolant level to the proper level.

Recycled Engine Coolant

Ford Motor Company does NOT recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available.

of in an appropriate manner. Follow your community’s regulations and standards for Used engine coolant should be disposed
of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.

Severe Climates

If you drive in extremely cold climates:

• It may be necessary to have a Ford authorized dealer increase the coolant concentration above 50%.

• A coolant concentration of 60% will provide improved freeze point protection. Engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.

If you drive in extremely hot climates:

• It may be necessary to have a Ford authorized dealer decrease the coolant concentration to 40%.

• A coolant concentration of 40% will provide improved overheat protection. Engine coolant concentrations below 40% will decrease the corrosion and freeze protection characteristics of the engine coolant and may cause engine damage.

Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection.

What You Should Know About Fail-Safe Cooling

If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred.

The fail-safe distance depends on ambient temperatures, vehicle load and terrain.

How Fail-Safe Cooling Works

If the engine begins to overheat:

• The engine coolant temperature gauge will move to the red (hot) area.

• The service engine soon indicator will illuminate.


• The service engine soon indicator will illuminate.

• The coolant temperature warning light will illuminate.


• The coolant temperature warning light will illuminate.

If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine.

When this occurs the vehicle will still operate. However:

• The engine power will be limited.

• The air conditioning system will be disabled.

Continued operation will increase the engine temperature and the engine will completely shut down, causing steering and braking effort to increase.

Once the engine temperature cools, the engine can be re-started. Take your vehicle to an authorized dealer as soon as possible to minimize engine damage.

When Fail-Safe Mode is Activated

You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine.

2. Arrange for the vehicle to be taken to an authorized dealer.

3. If this is not possible, wait a short period for the engine to cool.

4. Check the coolant level and replenish if low.

WARNING

: Fail-safe mode is for use during emergencies only.

Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs.

When in fail-safe mode, the vehicle will have limited power, will not be able to maintain high-speed operation, and may completely shut down without warning, potentially losing engine power, power steering assist, and power brake assist, which may increase the possibility of a crash resulting in serious injury.

WARNING

: Never remove the coolant reservoir cap while the engine is running or hot. The hot coolant is under pressure and may cause serious burns.

5. Re-start the engine and take your vehicle to an authorized dealer.

Note

: Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to an authorized dealer as soon as possible.

    Engine oil check
    Note: Check the level before starting the engine. Note: Make sure that the level is between the MIN and MAX marks. 1. Make sure that your vehicle is on level ground. 2. Turn the engine off and wait ...

    Transmission fluid check
    Checking Automatic Transmission Fluid Note: Transmission fluid should be checked and, if required, added by an authorized dealer. The automatic transmission does not have a transmission fluid dips ...

    Other materials:

    Brake Disc Machining
    Noise, Vibration and Harshness (NVH) (Description and Operation) Noise is any undesirable sound, usually unpleasant in nature. Vibration is any motion, shaking or trembling, that can be felt or seen when an object moves back and forth or up and down. Harshne ...

    Actuator Cable - Speed Control
    Speed Control (Diagnosis and Testing) Refer to Wiring Diagrams Cell 31 , Speed Control for schematic and connector information. Special Tool(s) Worldwide Diagnostic System (WDS) 418-F224, New Generation STAR (NGS) Tester 418-F052, or equi ...

    Pulley - CII Pump
    Power Steering (Description and Operation) System View Steering System Components - 3.8L Engine   Steering System Components - 4.6L Engine   Steering Gear Mounting   Steering Gear   Power Steering Pump - CII Power Steering ...