Ford Mustang (1999-2004) Service Manual: Inspection and Verification
Certain axle noise or vibration symptoms are also common to the engine, transmission, wheel bearings, tires, and other parts of the vehicle. For this reason, be sure that the cause of the trouble is in the axle before disassembling, adjusting or repairing the axle. Certain driveshaft vibration symptoms are common to the front engine accessory drive (FEAD), the engine, transmission or tires. Be sure the cause of the concern is the driveshaft before repairing or installing a new driveshaft. Certain symptoms may be caused by Traction-Lok differentials (4026). Check the vehicle certification label and axle identification tag to determine the type of differential.
Noise Acceptability
NOTE: A gear-driven unit will produce a certain amount of noise. Some noise is acceptable and audible at certain speeds or under various driving conditions such as a newly paved blacktop road.
Slight noise is not detrimental to the operation of the axle and is considered normal.
With the Traction-Lok differential axle, slight chatter noise on slow turns after extended highway driving is considered acceptable and has no detrimental effect on the locking axle function.
Universal Joint (U-Joint) Inspection
Place the vehicle on a frame hoist and rotate the driveshaft (4602) by hand. Check for rough operation or seized U-joints. Install a new U-joint if it shows signs of seizure, excessive wear, or incorrect seating.
Analysis of Leakage
Clean up the leaking area enough to identify the exact source. An axle leak can be caused by the following.
- Axle lubricant level is too high.
- Worn or damaged axle shaft seals or differential seals.
- Differential housing is cracked.
- Flange yoke seat is worn or damaged.
- Pinion flange is scored or damaged.
- Axle cover is not sealed.
- Vent is plugged.
Repair the axle as necessary. Make sure the axle lubricant is at the correct level. Refer to Specifications in this section.
Axle Vent
NOTE: If a plugged vent cannot be cleared, install a new one.
A plugged vent will cause excessive seal lip wear due to internal pressure buildup. If a leak occurs, check the vent. Make sure the vent hose is not kinked. Remove the hose from the vent nipple and clear the hose of any foreign material. While the hose is removed, pass a length of mechanics wire in and out of the vent to clean it. Connect the hose when done.
Flange Yoke Seal
Leaks at the axle drive pinion seal originate for the following reasons:
- Seal was not correctly installed.
- Poor quality seal journal surface.
Any damage to the seal bore (dings, dents, gouges, or other imperfections) will distort the seal casing and allow leakage past the outer edge of the axle drive pinion seal.
The axle drive pinion seal can be torn, cut, or gouged if it is not installed carefully. The spring that holds the axle drive pinion seal against the pinion flange may be knocked out and allow leakage past the lip.
The rubber lips can occasionally become hard (like plastic) with cracks at the oil lip contact point. The contact point on the pinion flange may blacken, indicating excessive heat. Marks, nicks, gouges, or rough surface texture on the seal journal of the pinion flange will also cause leaks.
When a seal leak occurs, install a new seal and check the vent and the vent hose to make sure they are clean and free of foreign material.
Axle Shaft Seals
Axle shaft oil seals are susceptible to the same kinds of damage as axle drive pinion seals if incorrectly installed. The seal bore must be clean and the lip handled carefully to avoid cutting or tearing it. The axle shaft journal surface must be free of nicks, gouges, and rough surface texture.
Driveline System
Special Tool(s) Clamp Plate 205-320 (T92L-4851-C) Clutch Housing Alignment Adapter 308-021 (T75L-4201-A) Companion Flange Holding Tool 205-126 (T78P-4851-A ...Analysis of Vibration
WARNING: A vehicle equipped with a Traction-Lok differential will always have both wheels driving. If only one wheel is raised off the floor and the rear axle is driven by the engine, the wheel on t ...Other materials:
Emission control system
WARNING: Do not park, idle, or drive your vehicle in dry grass
or other dry ground cover. The emission system heats up the
engine compartment and exhaust system, which can start a fire.
WARNING: Exhaust leaks may result in entry of harmful and
potentially leth ...
Refrigerant Lines
The condenser to evaporator tube (19835) contains the high pressure liquid
refrigerant upstream of the
evaporator core orifice.
The A/C manifold and tube (19D734) is attached to the A/C compressor, is sealed
with O-ring seals,
and has the following features ...
Front Subframe - 3.8L Engine
Special Tool(s)
3-Bar Engine Support Kit
303-F072
Lifting Bracket Set, Engine
303-D095 (D94L-6001-A) (014-
00792)
Removal and Installation
All vehicles
1. Remove the steering gear. For additional information, refer to Section.
...