Ford Mustang Service Manual: Installation

Removal

WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable mixtures are always present and can ignite. Failure to follow these instructions can result in personal injury.

1. With the vehicle in neutral, position it on a hoist. For additional information, refer to Section.

2. Disconnect the battery ground cable. For additional information, refer to Section.

3. Remove the upper intake manifold. For additional information, refer to Section..

4. Disconnect the following connectors:

  • The 42 pin engine bulkhead electrical connector.
  • The 16 pin electrical connector.

5. Separate the wiring harness from the dash panel.


5. Separate the wiring harness from the dash panel.

6. Remove the RH ignition coil cover.


6. Remove the RH ignition coil cover.

  • Remove the bolts.
  • Remove the coil cover.

7. Disconnect the RH ignition coil electrical connectors.


7. Disconnect the RH ignition coil electrical connectors.

8. Disconnect the heated positive crankcase ventilation (PCV) valve


8. Disconnect the heated positive crankcase ventilation (PCV) valve electrical connector.

9. Remove the LH ignition coil cover.


9. Remove the LH ignition coil cover.

  • Remove the bolts.
  • Remove the coil cover.

10. Disconnect the LH ignition coil electrical connectors.


10. Disconnect the LH ignition coil electrical connectors.

11. Disconnect the transmission main control harness electrical


11. Disconnect the transmission main control harness electrical connector.

12. Disconnect the engine control jumper harness electrical connector.


12. Disconnect the engine control jumper harness electrical connector.

13. Remove the wiring harness bracket bolt.


13. Remove the wiring harness bracket bolt.

14. Disconnect the RH heated oxygen sensor (HO2S) electrical connector.


14. Disconnect the RH heated oxygen sensor (HO2S) electrical connector.

15. NOTE: LH side is shown, RH side is similar.


15. NOTE

: LH side is shown, RH side is similar.

Disconnect the two radio ignition interference capacitor electrical connectors.

16. Disconnect the battery supply wire from the power distribution box


16. Disconnect the battery supply wire from the power distribution box stud.

17. NOTE: The electrical connector is located under the power


17. NOTE

: The electrical connector is located under the power distribution box.

Disconnect the electrical connector.

18. Disconnect the electrical connector.


18. Disconnect the electrical connector.

19. Disconnect the following generator electrical connectors:


19. Disconnect the following generator electrical connectors:

  • Battery power supply wire.
  • Voltage regulator.

20. Disconnect the camshaft position (CMP) sensor electrical connector.


20. Disconnect the camshaft position (CMP) sensor electrical connector.

21. Disconnect the engine coolant temperature (ECT) sensor electrical


21. Disconnect the engine coolant temperature (ECT) sensor electrical connector.

22. Remove the wiring harness.


22. Remove the wiring harness.

  • Separate the wiring harness from the LH valve cover stud bolt.
  • Separate the wiring harness from the power steering reservoir bracket.

Installation


    Removal
    Removal WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable mixtures are always present and can ignite. Fai ...

    Supply Manifold
    Fuel Charging and Controls The fuel injection supply manifold (9F792): delivers fuel to the fuel injector. receives fuel from the fuel supply line. The throttle body: controls air supply to the ...

    Other materials:

    Handles, Locks, Latches And Mechanisms (Description and Operation)
    Handles, Locks, Latches And Mechanisms (Description and Operation) Lock Cylinders Individual lock cylinders are repaired by discarding the inoperative lock cylinder and building a new lock cylinder using the appropriate lock repair package. The lock r ...

    Spark Plugs
    Engine Ignition (Description and Operation) The ignition coil (12029), which is mounted on the upper intake manifold, can be described as a coil pack containing three separate coil units. Each coil unit is individually controlled by the powertrain control mo ...

    Mass Air Flow (MAF) Sensor - 4.6L (2V)
    Electronic Engine Controls (Description and Operation) The electronic engine controls consist of the following: powertrain control module (PCM) throttle position (TP) sensor idle air control (IAC) valve engine coolant temperature (ECT) sensor ...