Ford Mustang Service Manual: Removal

Removal

1. Remove the rear exterior trim mouldings.

2. Remove the clips

3. Remove the 13 Torx screws and the seal compression panel.


3. Remove the 13 Torx screws and the seal compression panel.

4. Remove the staples.


4. Remove the staples.

5. Remove the staples from the number one bow.


5. Remove the staples from the number one bow.

6. Remove the rear rail weatherstrip retainers from each side.


6. Remove the rear rail weatherstrip retainers from each side.

7. Raise the front of the folding top assembly.


7. Raise the front of the folding top assembly.

8. Remove the screw and the center elastic straps.

9. Remove the speed nut and the front elastic straps.


9. Remove the speed nut and the front elastic straps.

10. Remove the screw and the front elastic strap.


10. Remove the screw and the front elastic strap.

11. Remove the screw and the rear elastic straps.


11. Remove the screw and the rear elastic straps.

12. Remove the screw and the rear elastic straps.


12. Remove the screw and the rear elastic straps.

13. NOTE: Install new plastic roof headlining retaining pins if they were


13. NOTE: Install new plastic roof headlining retaining pins if they were removed.

Disengage the roof headlining from the folding roof rear side rail.

14. Remove the screws from the number four bow.


14. Remove the screws from the number four bow.

15. Remove the screws from the number three bow.


15. Remove the screws from the number three bow.

16. Remove the screws from the number two bow.


16. Remove the screws from the number two bow.

17. Remove the headlining.


17. Remove the headlining.

18. Remove the nuts retaining the well sling and convertible top tacking strips.

19. Remove screws and the three tacking strips.


19. Remove screws and the three tacking strips.

20. Remove the staples.


20. Remove the staples.

21. NOTE: All adhesive tape must be removed from the folding roof rear side


21. NOTE: All adhesive tape must be removed from the folding roof rear side rail.

Pull the roof outside cover flaps to disengage from each folding roof rear side rail.

22. Remove the staples from the entire length of the number four bow.


22. Remove the staples from the entire length of the number four bow.

23. Disengage the cable from each side.


23. Disengage the cable from each side.

24. Remove the cable from the cover assembly.


24. Remove the cable from the cover assembly.

25. NOTE: The cable is spring-loaded. Use care not to lose the cable end


25. NOTE: The cable is spring-loaded. Use care not to lose the cable end during disassembly.

Disconnect the trim tension cable.

26. Remove the cover from the frame.


26. Remove the cover from the frame.

    Convertible Top Material
    Convertible Top (Description and Operation)   Rear Window Glass Assembly The convertible top assembly is equipped with a rear window glass assembly. The rear window glass assembly is p ...

    Installation
    Removal 1. Remove the rear exterior trim mouldings. 2. Remove the clips 3. Remove the 13 Torx screws and the seal compression panel. 4. Remove the staples. 5. Remove the staples from the nu ...

    Other materials:

    Exhaust Manifold LH
    Engine       A modular engine is built around four modules: the intake module the cylinder head module (RH) the cylinder head module (LH) the lower engine module While not all repairs can take advantage of the modular conc ...

    Accelerator Pedal and Shaft
    Acceleration Control (Description and Operation) Component Locations   The throttle is controlled by the accelerator cable which is connected to the accelerator pedal and shaft. The accelerator pedal and shaft should travel smoothly from the idle t ...

    Removal
    Removal 1. Disconnect the battery ground cable. For additional information, refer to Section. 2. Remove the engine air cleaner outlet pipe. For additional information, refer to Section. 3. Disconnect the vacuum hose and the idle air control (IAC) valv ...