Ford Mustang Service Manual: Removal

Removal

WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in personal injury.

WARNING: Fuel in the fuel system remains under high pressure even when the engine is not running. Before working on or disconnecting any of the fuel lines or fuel system components, the fuel pressure must be relieved. Failure to follow these instructions may result in personal injury.

1. Disconnect the battery ground cable (14301). For additional information, refer to Section.

2. Disconnect the air cleaner outlet tube. For additional information, refer to Section.

3. Relieve the fuel pressure. For additional information, refer to Section.

4. Disconnect the fuel line. For additional information, refer to Section..

5. Remove the throttle body (9E926). For additional information, refer to Throttle Body in this section.

6. Remove the idle air control (IAC) hose and position it out of the way.

7. Remove the positive crankshaft ventilation (PCV) hose.


7. Remove the positive crankshaft ventilation (PCV) hose.

8. Disconnect the four RH fuel injector electrical connectors.


8. Disconnect the four RH fuel injector electrical connectors.

9. Disconnect the IAC electrical connector and the main chassis vacuum


9. Disconnect the IAC electrical connector and the main chassis vacuum hose.

10. Remove the hose.


10. Remove the hose.

11. Squeeze the two locking tabs, and remove the accelerator cable and


11. Squeeze the two locking tabs, and remove the accelerator cable and the speed control cable (if equipped) and position aside.

12. Disconnect the fuel pressure sensor electrical connector and the


12. Disconnect the fuel pressure sensor electrical connector and the vacuum hose.

13. Disconnect the ground wire.


13. Disconnect the ground wire.

14. Disconnect the LH fuel injector electrical connectors.


14. Disconnect the LH fuel injector electrical connectors.

15. Remove the exhaust vacuum regulator (EVR) solenoid vacuum lines.


15. Remove the exhaust vacuum regulator (EVR) solenoid vacuum lines.

16. Remove the bolts from the EGR pressure transducer bracket and


16. Remove the bolts from the EGR pressure transducer bracket and position aside.

17. Remove the EGR to exhaust manifold tube. For additional information,


17. Remove the EGR to exhaust manifold tube. For additional information, refer to Section.

18. Disconnect the exhaust valve recirculation (EGR) vacuum line.

19. NOTE: The LH side is shown, the RH is similar.


19. NOTE

: The LH side is shown, the RH is similar.

Remove the four bolts and remove the supply manifold with the fuel injectors attached.

Installation


    Fuel Injection Supply Manifold
    Fuel Charging And Controls The fuel injection supply manifold (9F792): delivers fuel to the fuel injector. receives fuel from the fuel supply line. The throttle body (9E926): controls air supply ...

    Installation
    Removal WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable mixtures are always present and may be ignited. ...

    Other materials:

    Checking MyKey system status
    You can find information about your programmed MyKeys by using the information display. MYKEY DISTANCE Tracks the distance when drivers use a MyKey. The only way to delete the accumulated distance is by using an admin key to clear your MyKey. If the dis ...

    Material
    Material Item Specification Threadlock and Sealer E0AZ-19554-AA WSK-M2G351-A5 (type II) Shoulder Bolt Kit F5ZZ-76539A04-A - NOTE: Before starting the adjustment process, inspect the top for damage, make sure that the door win ...

    Fastening the safety belts
    The front outboard and rear safety restraints in your vehicle are combination lap and shoulder belts. The presenter arm (available on the coupe only) is intended to improve access to the safety belt and to allow access to the rear seat. Rotate the pres ...