Ford Mustang Service Manual: Lamp Switch - Brake Pedal Position (BPP)
Headlamps
Refer to Wiring Diagrams Cell 85 , Headlamps for schematic and connector information.
Special Tool(s)
73III Automotive Meter or equivalent 105-R0057 |
Inspection and Verification
1. Verify the customer concern by operating the headlamps.
2. Visually inspect for the following obvious signs of mechanical and electrical damage.
Visual Inspection Chart
Mechanical | Electrical |
|
|
3. If the concern is not visually evident, determine the symptom and proceed to Symptom Chart.
Symptom Chart
Condition | Possible Sources | Action |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pinpoint Tests
PINPOINT TEST A: BOTH HEADLAMPS ARE INOPERATIVE
Test Step | Result / Action to Take |
A1 CHECK THE VOLTAGE TO THE HEADLAMP SWITCH | Yes GO to A2 . No REPAIR the circuit. TEST the system for normal operation. |
|
|
A2 CHECK CIRCUIT 15 (RD/YE) FOR OPEN | Yes RECONNECT headlamp switch C205. GO to A3 . No REPAIR the circuit. TEST the system for normal operation. |
|
|
A3 CHECK THE VOLTAGE TO THE MULTIFUNCTION SWITCH | Yes INSTALL a new multifunction switch; REFER to Section. TEST the system for normal operation. No INSTALL a new headlamp switch; REFER to Lamp Switch-Headlamp in this section. TEST the system for normal operation. |
|
PINPOINT TEST B: THE LOW BEAMS ARE INOPERATIVE
Test Step | Result / Action to Take |
B1 CHECK THE VOLTAGE TO CJB FUSE 4 (7.5A) AND CJB FUSE 10 (7.5A) | Yes Go To Pinpoint Test D . No GO to B2 . |
|
|
B2 CHECK CIRCUIT 13 (RD/BK) FOR OPEN | Yes INSTALL a new multifunction switch; REFER to Section. TEST the system for normal operation. No REPAIR the circuit. TEST the system for normal operation. |
|
PINPOINT TEST C: THE HIGH BEAMS ARE INOPERATIVE
Test Step | Result / Action to Take |
C1 CHECK THE CIRCUIT 12 (LG/BK) | Yes RECONNECT the LH headlamp (13008). GO to C2 . No REPAIR the circuit. TEST the system for normal operation. |
|
|
C2 CHECK THE VOLTAGE TO CJB FUSE 38 (20A) | Yes Go To Pinpoint Test E . No GO to C3 . |
|
|
C3 CHECK CIRCUIT 632 (GY/OG) FOR OPEN | Yes INSTALL a new multifunction switch; REFER to Section. TEST the system for normal operation. No REPAIR the circuit. TEST the system for normal operation |
|
PINPOINT TEST D: ONE LOW BEAM HEADLAMP IS INOPERATIVE
Test Step | Result / Action to Take |
D1 CHECK THE VOLTAGE TO THE INOPERATIVE HEADLAMP BULB | Yes INSTALL a new headlamp bulb; REFER to Bulb-Headlamp in this section. TEST the system for normal operation. No REPAIR the circuit. TEST the system for normal operation. |
|
PINPOINT TEST E: ONE HIGH BEAM HEADLAMP IS INOPERATIVE
Test Step | Result / Action to Take |
E1 CHECK THE VOLTAGE TO THE INOPERATIVE HEADLAMP BULB | Yes INSTALL a new headlamp bulb; REFER to Bulb- Headlamp in this section. TEST the system for normal operation. No REPAIR the circuit. TEST the system for normal operation. |
|
PINPOINT TEST F: THE HEADLAMPS ARE ON CONTINUOUSLY
Test Step | Result / Action to Take |
F1 CHECK THE HEADLAMP SWITCH | Yes GO to F2 . No INSTALL a new headlamp switch; REFER to Lamp Switch-Headlamp in this section. TEST the system for normal operation. |
|
|
F2 CHECK THE MULTIFUNCTION SWITCH | Yes GO to F4 . No GO to F3 . |
|
|
F3 CHECK CIRCUIT 15 (RD/YE) FOR SHORT TO POWER | Yes REPAIR the circuit. TEST the system for normal operation. No INSTALL a new multifunction switch; REFER to Section 211- 05 . TEST the system for normal operation. |
|
|
F4 CHECK CIRCUIT 13 (RD/BK) FOR SHORT TO POWER | Yes REPAIR the circuit. TEST the system for normal operation. No GO to F5 . |
|
|
F5 CHECK CIRCUIT 1056 (DB, LG) FOR VOLTAGE | Yes REPAIR Circuit 1056 (DB/LG). TEST the system for normal operations. No REPAIR Circuit 1055 (WH/LG). TEST the system for normal operations. |
|
Lamp Switch - Headlamp
Headlamps Refer to Wiring Diagrams Cell 85 , Headlamps for schematic and connector information. Special Tool(s) 73III Automotive Meter or equivalent 105-R0057 Inspection and V ...Interior Lighting
Interior Lighting The interior lighting system consists of the following: map/dome lamp assembly rear-high mount/cargo lamp assembly dimmer switch door ajar switch (located on the door latc ...Other materials:
Keyless Entry/Computer Operated Locks
Programming -Keyless Entry Remote Transmitter
NOTE: All keyless entry remote transmitters (15K601) must be
programmed at the same time.
NOTE: All previous transmitter identification codes (TIC's) will be
erased when programming mode is
entered.
...
Gearshift Rail and Fork
Manual Transmission
The T56 six-speed manual transmission features the following:
six forward speeds and one reverse speed.
forward gears are synchronized and helical cut.
a reverse gear operates through a constant-mesh, fully synchronized
system.
a shi ...
Child Safety
GENERAL INFORMATION
See the following sections for directions on how to properly use safety restraints
for children.
WARNING: Always make sure your child is secured properly in a device that
is appropriate for their height, age and weight.
Child safety ...