Ford Mustang (1999-2004) Service Manual: Automatic Transaxle/Transmission
General Specifications
a - MERCON V is not interchangeable at this time with the current MERCON fluids. Check the transmission fluid level indicator to determine the correct fluid and refer to the Workshop/Owner publication to determine the correct service interval for the specific vehicle.
Torque Converter End Play
Band and Clutch Application Chart
A = Applied
H = Holding
O/R = Overrunning
Stall Speed
Shift Speeds 4.6L 4V MACH 1 (3.55:1 Axle Ratio)
Shift Speeds 4.6L 2V HO (3:27:1 Axle Ratio)
Shift Speeds 3.8L (3:27:1 Axle Ratio)
Shift Speeds 3.8L (3:08:1 Axle Ratio)
Sensor Resistance Readings
Selective Thrust Washer No.1
Forward Clutch Pack
Reverse Clutch Pack
Direct Clutch Pack
Intermediate Clutch Pack
Torque Specifications
- Transmission Description (Description and Operation)
- Identification Tags
- Range Selection
- Shift Patterns
- Torque Converter (Description and Operation)
- Geartrain
- Apply Components
- Hydraulic System
- Transmission Electronic Control System
- Diagnostic Strategy
- Preliminary Inspection
- Shift Point Road Test
- Torque Converter Diagnosis
- Diagnostics
- Output State Control (OSC) Mode
- Transmission Drive Cycle Test
- Diagnostic Trouble Code Charts
- Transmission Connector Layouts
- Pinpoint Tests - OSC Equipped Vehicles
- Special Testing Procedures
- Leakage Inspection
- Transmission Fluid Cooler
- Diagnosis By Symptom
- Transmission Fluid Cooler - Backflushing and Cleaning
- Transmission Fluid Drain and Refill
- Fluid Pan, Gasket and Filter
- Transmission Filler Tube
- Main Control Valve Body
- Extension Housing Seal and Gasket
- Electronic Pressure Control (EPC) Solenoid
- Manual Control Lever Shaft and Seal
- Digital Transmission Range (TR) Sensor
- Reverse Servo Assembly
- Overdrive Servo
- 1-2 Accumulator
- 2-3 Accumulator
- Transmission Support Crossmember
- Transmission (REMOVAL)
- Transmission (DISASSEMBLY)
- Main Control Valve Body
- Pump and Intermediate Clutch Piston
- Intermediate One-Way Clutch
- Reverse Clutch
- Forward Clutch Cylinder
- Planetary Gear Support Assembly and Planetary One-Way Clutch
- Reverse Sun Gear
- Output Shaft and Direct Clutch Cylinder
- Torque Converter (Disassembly and Assembly of Subassemblies)
- Torque Converter Cleaning And Inspection
- Torque Converter Leak Check
- Torque Converter Impeller to Pump Stator Interference Check
- Torque Converter End Play Check
- Torque Converter Turbine to Pump Stator Interference Check
- Transmission (ASSEMBLY)
- Transmission (INSTALLATION)
Transmission Description (Description and Operation)
The 4R70W has the following features:
Wide ratio gears
Four speeds
Rear wheel drive
Automatic
Electronic shift
Torque converter clutch control
Line pressure controls
The t ...
Other materials:
Transmission (Disassembly)
Special Tool(s)
Bearing Puller
205-D064 (D84L-1123-A) or
Equivalent
Front Hub Tool
204-069 (T81P-1104-C)
Holding Fixture
307-003 (T57L-500-B)
Impact Slide Hammer
100-001 (T50T-100-A)
Puller
...
Lumbar Motor
Removal and Installation
All vehicles
1. Remove the front seat. For additional information, refer to Seat-Front
Power in this section.
2. Disconnect the power seat track electrical connector.
3. Remove the four seat track bolts.
Vehicles with standar ...
Removal
All vehicles
WARNING: To prevent glass splinters from entering eyes or
cutting hands, wear safety
glasses and heavy gloves when cutting glass from the vehicle.
1. Remove the RH and LH windshield side garnish mouldings.
If equipped with a convert ...
